Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Problem flashing from Linux
#11
(06-20-2018, 09:27 AM)jhendryUK Wrote: Hi,

I started to followed the instructions to backup the NVRAM information which failed with this error:

Code:
BROM Exception! ( ERROR : STATUS_PROTOCOL_ERR (-1073676283) , MSP ERROE CODE : 0x00.

   
Since then my gemini does not power on anymore, I am hoping its not bricked!  Full output from the command line is here:

Code:
jhendry@twigz ~/dev/gemini/FlashToolLinux/ $ sudo ./flash_tool.sh
libpng warning: iCCP: known incorrect sRGB profile
QMetaObject::connectSlotsByName: No matching signal for on_pushButton_browser_clicked()
QThread::setPriority: Cannot set priority, thread is not running
"06-19-2018"
libpng warning: iCCP: known incorrect sRGB profile
QObject::moveToThread: Cannot move objects with a parent
libpng warning: iCCP: known incorrect sRGB profile
Connecting to BROM...
Scanning USB port...
Search usb, timeout set as 3600000 ms
add@/devices/pci0000:00/0000:00:14.0/usb1/1-2

add@/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0

add@/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1

bind@/devices/pci0000:00/0000:00:14.0/usb1/1-2

add@/module/cdc_acm

bind@/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1

add@/devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/tty/ttyACM0

vid is 0e8d

device vid = 0e8d

pid is 2000

device pid = 2000

com portName is: /dev/ttyACM0

Total wait time = -1529482163.000000
USB port is obtained. path name(/dev/ttyACM0), port name(/dev/ttyACM0)
USB port detected: /dev/ttyACM0
BROM connected
Downloading & Connecting to DA...
connect DA end stage: 2, enable DRAM in 1st DA: 0
Failed to Connect DA: STATUS_PROTOCOL_ERR
Disconnect!
BROM Exception! ( ERROR : STATUS_PROTOCOL_ERR (-1073676283) , MSP ERROE CODE : 0x00.


[HINT]:
)((ConnectDA,../SP-Flash-Tool-src/Conn/Connection.cpp,131))
comboTimeout index(3) saved.



When I first connected the device dmesg recognised at as:

Code:
[ 1964.099253] usb 1-2: new high-speed USB device number 11 using xhci_hcd
[ 1964.248234] usb 1-2: New USB device found, idVendor=0e8d, idProduct=2000
[ 1964.248240] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1964.248243] usb 1-2: Product: MT65xx Preloader
[ 1964.248247] usb 1-2: Manufacturer: MediaTek
[ 1964.371647] cdc_acm 1-2:1.0: ttyACM0: USB ACM device
[ 1964.410364] usbcore: registered new interface driver cdc_acm
[ 1964.410365] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1983.203287] cdc_acm 1-2:1.0: failed to set dtr/rts


Now it gets this error:

Code:
[ 2399.573301] usb 1-2: new high-speed USB device number 15 using xhci_hcd
[ 2404.713497] usb 1-2: device descriptor read/64, error -110


Any ideas what has happened or what I can do? This was done on Ubuntu 18.04 LTS using the Linux flashtool linked by gidds.


Figured out how to make it boot!  The system was stuck in some strange state (unknown), holding down both Esc+SideButton triggered a hard reboot.   Its booting now and ready to try again Smile
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)